Product description

Klüberoil 4 UH 1 N oils are lubricating oils based on polyalphaolefin. Klüberoil 4 UH 1 N oils meet the CLP requirements according to DIN 51517-3.

Benefits for your application

• Requirements set forth in DIN 51517-3,CLP are met by viscosity variants ISO VG 68 to 680. Klüberoil 4 UH1 N oils can be used in gearboxes requiring these standards without prior consent by the gearbox OEM if the application notes are observed.

• Registered as NSF H1 for use in the food-processing and pharmaceutical industries, comply with FDA 21 CFR Sec 178.3570.

• NSF ISO 21469 certified - supports the compliance with the hygienic requirements in your production plant. You will find further information on ISO Standard 21469 on our website www.klueber.com.

• Having a synthetic polyalphaolefin base oil, Klüberoil 4 UH1 N oils have a significantly prolonged service life compared to mineral and white oil due to the base oil’s excellent ageing resistance and oxidation stability. Service intervals can be extended and in some cases even lifetime lubrication can be achieved.

• Due to the wide service temperature range, it is often sufficient to use just one viscosity grade for both high and low temperatures.

• The good viscosity-temperature behaviour supports the formation of a sufficient lubricating film, also under elevated or high temperatures.

• Due to the oils’ good wear protection for both the gear teeth and the rolling bearings, the lubricated components attain their calculated lifetime.

Product description

Klübersynth UH1 14-31 was especially devel­oped for the food-processing and pharmaceutical industries. This lubricant is NSF H1-registered and therefore complies with FDA 21 CFR § 178.3570.

Benefits for your application

• Reliable operation also at low temperatures due to soft consistency and low base oil viscosity

• Reduced risk of premature component failure due to good adhesion and anticorrosive behaviour

• Lubricant starvation prevented by very good pumpability in centralised lubricating systems

• NSF-H1 registration for higher process reliability

Product description

MICROLUBE GL 261, GL 262 greases are special lubricating greases on a mineral oil base. They also contain special lithium soap and the MICROLUBE additive package, which ensures a wear-free surface finish. Running-in wear is reduced to a minimum. In addition, the MICROLUBE additive package provides protection in the boundary friction regime, thus preventing tribo-corrosion. MICROLUBE GL 261, GL 262 greases have the capacity to absorb high pressures, and they have good anti-corrosion properties.

Benefits for your application

• Optimum lubrication in the boundary friction regime, thus preventing machine downtime due to tribo-corrosion

• Tried-and-tested for many years and approved by OEMs

• Longer component life due to special additives, especially with oscillations and micro-movements

• Trouble-free operation of machines due to good pumpability in central lubrication systems

Product description

STABURAGS NBU 30 is a lubricating grease based on mineral oil and a barium complex soap.

Benefits for your application

• Long component life due to good corrosion protection in humid and aggressive environment

• Good resistance to water, water vapor and many diluted alkaline and acidic solutions

• Good sealing characteristics, even with water, hot water, water vapor and aggressive media

• High wear protection in a wide range of mechano-dynamical loads and at high surface pressures

• NSF H2-approved

Product description

Wolfracoat C is a grey high-temperature lubricating paste containing metal solid lubricant pigments (e.g. copper, graphite). Wolfracoat C counteracts excessive friction, wear and seizing at lubricating points subject to high loads. Wolfracoat C forms a thermally stable lubricating film. At temperatures above 200 °C, the solid lubricants remain in the friction points and protect against tribocorrosion and fretting of e.g. fits up to 1200 °C.

Benefits for your application

• Easier assembly and disassembly of power-locking connections

• Reliable lubrication under mixed-friction and high-load conditions owing to ageing-resistant solid lubricantS

Product description

Klüberplex BEM 34-132, BEM 34-131 N are based on synthetic hydrocarbon oil, mineral oil and special calcium soap. They are used for the lubrication of rolling bearings, sliding bearings, linear guides and small gears operating under high loads.

Benefits for your application

• Long service intervals due to excellent wear protection and ageing resistance enabling long-term or lifetime lubrication

• Reliable function and many years of experience

• Standardization possible due to multiple uses

• Very good function of the rolling bearings due to high load resistance also with micro-movements

• Longer rolling bearing life due to excellent corrosion protection and resistance to media

Product description

Klübersynth UH1 14-1600 is a synthetic high-performance lubricating grease. It is registered as NSF H1 and complies with FDA 21 CFR Sec. 178.3570. Klübersynth UH1 14-1600, an NSF H1-registered lubricant, is a contributor towards the supporting of food safety. The use of this lubricant needs to be considered not in isolation but in line with other appropriate actions which have by law to be fulfilled by a food manufacturing plant to allow for food to be manufactured safely. Its soft consistency, good wear protection and scuffing load stage 11 in the FZG test ensure good lubricant distribution and reduced wear in the gear.

Benefits for your application

• Improved pumpability due to its soft consistency

• Component life enhanced resulting from a special thickener with good adhesion and good corrosion protection

• ISO 21469 certified – supports the compliance with the hygienic requirements in your production.

Product description

Metalstar KS 201 ... 203 are water-miscible die dressings for gravity and low pressure diecasting of aluminum alloys. They are based on silicate, solid lubricants and water. Casting and flow behaviour depend on the layer lattice structure of the solid lubricants in the die dressing. METALSTAR KS 210 is based on synthetic hydrocarbon oil and solid lubricants. It is a non water-miscible die dressing which extends the service life of riser stalks.

Product description

ISOFLEX TOPAS NB 52 and ISOFLEX TOPAS NB 152 are rolling and plain bearing greases based on a synthetic hydrocarbon oil and a barium complex soap. The special barium-soap thickener used in the ISOFLEX TOPAS NB 52 and 152 greases offers good load-carrying capacity as well as resistance to water and ambient media unlike other soap-based thickeners. Both products show good protection against corrosion as well as oxidation and ageing stability. The Klüber barium complex soap is ELINCS-registered and approved by GASG (Global Automotive Stakeholders Group).

Benefits for your application

• Longer component life when exposed to water or aqueous media due to special thickener

• Many years of successful use in the automotive and machine building industries

Product description

Wolfracoat C is a grey high-temperature lubricating paste containing metal solid lubricant pigments (e.g. copper, graphite). Wolfracoat C counteracts excessive friction, wear and seizing at lubricating points subject to high loads. Wolfracoat C forms a thermally stable lubricating film. At temperatures above 200 °C, the solid lubricants remain in the friction points and protect against tribocorrosion and fretting of e.g. fits up to 1200 °C.

Benefits for your application

• Easier assembly and disassembly of power-locking connections

• Reliable lubrication under mixed-friction and high-load conditions owing to ageing-resistant solid lubricants

Product description

Klüberquiet BQ 74-73 N is a rolling bearing grease based on synthetic hydrocarbon, ester oil and urea. It was especially developed for the lubrication of high-speed ball bearings operating at high temperatures. With its unique combination of carefully selected raw materials, Klüberquiet BQ 74-73 N offers

Benefits for your application

• Lifetime lubrication of vertically mounted bearings subject to high speeds and/or with a rotating outer ring

• Low-noise spindle bearing grease, also for motor spindles

Product description

Klübersynth UH1 14-151 was especially developed for the food processing and pharmaceutical industry. Klübersynth UH1 14-151 shows good anti-wear properties, water resistance and corrosion protection as well as a high ageing and oxidation stability.